Supply & Return Duct Cleaning in Dripping Springs
Targeted source removal for the runs that actually need it.
01Dripping Springs — the housing record
What Dripping Springs actually has behind its walls.
Before anyone quotes a duct job here, this is the stock they are quoting against. It is public Census data, and it is different in every city we cover.
- Housing units
- 2,605
- Built pre-1980
- 0%
- Built 2000s
- 21%
- Built since 2010
- 66%
- Gas heat
- 18%
- Electric heat
- 70%
- Single-family
- 51%
U.S. Census Bureau, American Community Survey 5-Year Estimates (2023), tables B25034, B25040 and B25024. Percentages are rounded and describe the city, not your house.
What that means for ducts
New-build ductwork
Roughly 66% of Dripping Springs's homes were built since 2010. New does not mean clean: the commonest thing we pull out of a five-year-old system is the construction phase itself — drywall fines, sawdust, insulation fiber — plus builder-grade flex that was kinked or crushed on the day and has been throttling that run ever since. Photographs matter more here, not less.
That is a reading of the city’s stock, not a diagnosis of your home. Which of it applies to you is exactly what the camera settles — and why we would rather run one than quote from a postcode.
02Working in Dripping Springs
The part that changes from street to street.
Two different jobs share the Dripping Springs name. Inside the actual city limits the housing is recent and roughly half of it is attached, apartments and townhomes near the center, each running an air handler in a closet with barely any duct hanging off it. Everything else people mean by Dripping Springs is county acreage, larger houses on unpaved drives, commonly with two systems and long attic trunks reaching wings that sit far apart. On those properties the largest single influence on the inside of your ductwork is the driveway and the road it meets. Caliche and crushed limestone throw a fine pale dust every time a vehicle moves, and it comes in on shoes, through doors held open, and directly into any return joint that is not sealed. Filters at the end of a long gravel drive load faster than filters in town, and the answer to that is a schedule rather than a scrubbing. Gas service barely reaches out here, so most homes run heat pumps and a few burn propane, which is worth establishing before anyone opens a cabinet.
Hamilton Pool Preserve
- Belterra ·
- Caliterra ·
- Headwaters ·
- Historic Mercer Street
County
Hays County
Same standard in Dripping Springs as everywhere else.
Source removal to the NADCA ACR standard, a written quote before anything is touched, and camera photographs of your own runs before and after. We are not going to re-argue that on every city page — it is set out once, in full, on the service page.
- Camera confirmation of which runs need work before you approve anything
- Negative-pressure source removal on the affected trunks and branches
- After photos of every cleaned run
- A written note of the runs verified clean and left alone
- From
- $199
- On site
- 2–3 hours
- Scope
- 4 lines
Prices shown are starting estimates and may change with the condition, access, and scope we find on site. Only a written quote from an on-site visit is a price we commit to.
03Supply & Return Duct Cleaning — in this stock
Cleaning a system that is still carrying its own build.
A post-2010 system is usually not dirty in the way people picture. What comes out is the construction phase — drywall fines, sawdust, insulation fiber — that was pulled into open ducts before the house was ever occupied, plus whatever a kinked flex run has been collecting behind the crimp. That is a different cleaning: shorter, more targeted, and far more dependent on the before-and-after photographs, because the difference is not something you can smell.
How do you know cleaning part of the system is enough?
The camera decides, not a hunch. We scope the whole system first; if debris is concentrated in the returns or specific branches, we clean those and document the rest as verified clean.
Why are return ducts dirtier than supply ducts?
Because they run upstream of the filter. Returns pull raw room air — dust, pet hair, fibers, pollen tracked in on shoes — straight into the ductwork before anything filters it.
04Book in Dripping Springs
Three fields, and a person calls you back.
Tell us the ZIP and we will tell you what your system likely needs — including, sometimes, that it needs nothing yet. Nothing is charged until you have approved a written quote.
05Questions
Asked in Dripping Springs, answered straight.
How do you know cleaning part of the system is enough?
The camera decides, not a hunch. We scope the whole system first; if debris is concentrated in the returns or specific branches, we clean those and document the rest as verified clean. If footage shows buildup everywhere, we'll say a full cleaning is the honest recommendation — with the photos to prove it.
Why are return ducts dirtier than supply ducts?
Because they run upstream of the filter. Returns pull raw room air — dust, pet hair, fibers, pollen tracked in on shoes — straight into the ductwork before anything filters it. Supplies only see air the filter has already scrubbed. That asymmetry is why return-side cleaning is often the smartest partial job.
Our filters go gray in a month and we are well outside town.
That is the caliche drive, not a duct full of dirt. Limestone road dust is fine enough to stay airborne and it arrives continuously, so the system keeps catching it. Sealing the return joints stops the share coming in through leaks. The rest is a filter schedule, and we would rather write you a realistic one than sell a cleaning that the next few weeks of traffic undoes.
We have two systems. Do both need to be done?
Usually not. On these spread-out plans one system serves the main living area and runs constantly while the other covers a wing or a guest side that is barely used, and their conditions diverge quickly. We scope each and quote only what needs work. Being told that one of your two systems is fine is a normal outcome of this visit.
We are building on acreage. What should we watch during construction?
The distances more than the dust. Long single-story plans out here push flex runs well past what the design intended, and once the drywall is up nobody sees a run that was left slack or turned twice to reach a far bedroom. Ask to see the duct layout before it is covered, and have the boots capped through the finish trades. Fixing geometry before closing is far cheaper than living with it.
Last reviewed: